Describe whether the porch is open, screened, or enclosed, and which part gets wet. Tell the roofer whether the porch was added after the house was built. On a Gainesville home with several renovations, the history can help identify what drawings or concealed areas need closer review.

1. Locate the first visible water

Photograph the stain or drip from a safe position and identify the nearby wall, door, or corner. Record whether water first appears at the house connection, toward the outside edge, or in the middle of the porch ceiling.

Give the roofer a short timeline. Include previous repairs, when the leak returned, and whether it appears in wind-driven rain or ordinary rainfall. Your observations can guide the inspection without proving the entry point. Avoid painting over or covering the visible evidence before it has been documented, unless a professional advises an immediate protective action.

2. Identify the roofing on each side of the connection

Ask what covers the main roof and what covers the porch. A porch may have a different roof material or a different slope even when the colors look similar from the yard. Request that both sections appear on the inspection drawing.

If the main house has Owens Corning shingles, that does not establish the correct roofing system for every attached surface. Ask the contractor to identify the porch material and its applicable instructions. Have the estimate name the products proposed for the junction rather than assuming the main roof's material description covers it.

3. Have the porch slope and drainage evaluated

Ask the roofer to measure and document the porch roof's slope where it affects material selection. A homeowner's description of “almost flat” is useful background, but it cannot replace the measurements needed for the repair design.

Discuss the route water takes from the upper roof and any gutters or downspouts above the porch. Ask whether the proposed work addresses that route. If the contractor identifies a drainage problem, request an explanation of what changes and who performs the work. A roofing estimate and a gutter estimate should describe how their scopes meet at the same location.

4. Review the wall and flashing connection

Where the roof meets a wall, ask how the flashing connects with the wall's water-management layers. The Building America Solution Center's roof-to-wall flashing guidance explains why these connections need coordinated flashing details, including water discharge at the lower end.

Have the contractor explain what can be inspected now and what may require opening a concealed area. Ask whether siding, stucco, trim, or interior finish work is included. If it is excluded, identify the trade and next step before authorizing a repair that depends on someone else's unfinished work.

5. Separate a temporary measure from the proposed repair

If active leaking requires temporary protection, ask what that work is intended to do and what still needs evaluation. Record its date, cost, and planned follow-up. A temporary measure should have a clear place in the repair plan.

For the permanent proposal, request the specific repair boundary and the finding it addresses. Ask what materials will be removed, retained, or replaced. If the new scope resembles the repair that already failed, ask what new information supports doing it again. The answer may explain a different defect, a larger boundary, or a change in the proposed detail.

6. Ask whether hidden damage changes the work

Discuss possible concealed conditions before material is removed. Ask how the contractor will document findings, explain additional costs, and obtain approval. If framing or a structural connection appears to need evaluation, ask who will provide it.

Request photographs labeled by location, particularly if you will be away during the repair. A picture of damaged material should be linked to the relevant part of the porch. If the repair expands into the main roof, confirm whether that affects the agreed scope, schedule, and products. Keep each revision with the original proposal.

7. Define how the repair will be reviewed afterward

Ask what completion documentation you will receive and how any follow-up assessment will be performed. If the contractor proposes testing, let the qualified team plan and carry it out. Do not reproduce a water test yourself from an online description.

Record whom to contact if water reappears and which observations will help. Keep the original leak photographs so you can distinguish an old mark from a visible change. Ask how drying and interior or porch-ceiling restoration should be coordinated after the source is addressed. Finish work should follow that plan rather than obscuring an unresolved concern.

Prepare a porch connection brief

Write a single page with the porch type, known construction history, first wet location, rain pattern, and previous repair dates. Add a ground-level photograph showing the porch attached to the house. Mark anything you do not know.

Send that brief when requesting roof repair from Brehm Roofing in Gainesville. Ask for the main roof, porch roof, and their connection to be considered together, with the proposed repair boundary explained before work begins.

Set the request before work begins. The crew needs to know which stages you want documented while those stages are still visible. Photographs support the project record; they do not replace inspections or prove every hidden installation detail. You can review the images from the ground without entering the work area or climbing onto the roof.

1. An overall view before removal

Request a wide view that identifies the main roof, garage, porch, and additions included in the contract. Ask for location labels if the roof has several sections that look alike. This establishes the map for the rest of the photo record.

For a Gainesville home with a rear addition, include an angle that shows how that addition connects to the house. A front elevation alone may miss the area that prompted the project. Keep this photograph with the marked scope drawing and original estimate.

2. The property condition around the work area

Document the driveway, nearby landscaping, screened enclosure, gutters, and other surfaces close to the work. Take your own ground-level photographs before delivery if you can do so safely. Point out existing damage during the preparation meeting.

Use the record to identify specific locations if a question arises later. A dated image of the driveway near a container is more useful than a vague memory of its condition. Ask the contractor how property concerns should be reported and documented during the project.

3. Exposed decking after tear-off

Ask for wide photographs of the roof deck after removal and before covering. Request labels that match the initial roof map. The goal is to understand the surface the crew encountered and the areas selected for closer evaluation.

If only a small portion appears in a photograph, ask what other areas were inspected. A close-up of sound-looking wood cannot represent the entire roof. Keep the contractor's written findings beside the images so the record states what was observed rather than inviting you to diagnose the deck yourself.

4. Any condition behind an added charge

For additional work, request a close-up and a wider location photograph. Ask the project contact to explain the finding, the proposed repair boundary, and how the image relates to the quoted quantity.

Save the photographs with the written change request and approval. This prevents a series of messages from becoming detached from the final invoice. If the finding requires further investigation, ask for that limitation to be recorded. The photo should explain why a decision is needed, even when the full extent is not yet known.

5. Completed decking repairs before covering

Request an after photograph from a similar position to the original finding. Matching labels help you pair the repair with the approved change. Ask the contractor to identify any further work shown in the picture that was not part of the original request.

If the work involves an inspection before covering, confirm how that inspection will be handled. Photographs and inspection records have different jobs. Keep both where applicable, and ask which record establishes the current status of that project stage.

6. Underlayment and the relevant roof details

Ask for views that identify the installed underlayment and show the areas the contractor wants to document before shingles conceal them. The useful locations may include edges, valleys, penetrations, and connections to other roof sections.

Have the contractor identify the product and explain the view. A roll wrapper alone does not show where the material was installed; an unlabelled close-up may not identify the product. Pair the product record with the stage photographs and the agreed material list.

7. Flashing at walls and roof transitions

Request photographs of the junctions included in the scope, particularly any location connected with a previous leak. Ask for a sequence if the completed work will conceal the connection.

Name the feature in everyday language as well as roofing terminology: “back porch beside kitchen wall,” for example. That label remains useful years later when another contractor needs to locate the repair. If siding or wall work is outside the scope, have the project notes explain the boundary and any remaining responsibility.

8. Pipe boots, vents, and other penetrations

Ask for photographs of the roof penetrations included in the contract and a note identifying which components were replaced. Include any retained item that the contractor evaluated. A completed roof overview can make these small details difficult to distinguish.

For solar equipment, antennas, or other work by separate trades, identify which company documents its own work. Avoid treating the roofing contractor's photographs as confirmation that every piece of equipment was disconnected, reinstalled, or tested by the appropriate person.

9. Shingle product labels and installation details

Request a readable label showing the selected Owens Corning product and color, along with representative installation photographs the contractor considers useful. Owens Corning's Duration literature identifies SureNail technology within the Duration line; confirm the actual product on your proposal before applying product-specific descriptions.

Ask the contractor to explain the details shown. A homeowner photo review should not become an improvised fastening inspection. The purpose is a traceable product and work record, supported by the installer's documentation and applicable inspections.

10. The completed roof and cleanup

Finish with views that correspond to the initial roof map. Include the less-visible porch or addition as well as the front of the house. Request ground-level photographs of the staging area after equipment removal if that occurs later.

During the walkthrough, connect any remaining question to a labeled photograph. Record the responsible person and next action. Keep unresolved items visible in the project notes instead of losing them in a long text-message thread containing the entire photo collection.

Organize the record by stage

Use folders named Before, Exposed Roof, Repairs, Installation, and Completed. Keep change approvals beside the related repair photographs. Download copies you can retain, and ask permission before using any image publicly.

Tell Brehm Roofing which photo records you would like when planning your Gainesville roof replacement. Agree on the documentation before the crew reaches the work that will be covered.

For a Gainesville house with additions, enclosed porches, or past insulation changes, the visible roofline may not reveal how the attic spaces connect. Ask the roofer to explain the existing arrangement and mark the proposed changes. You should understand which part of the house the work is intended to serve.

1. Establish whether the attic is intended to be vented

Tell the contractor what you know about the attic's insulation. Mention spray foam at the underside of the roof, recent insulation work, or a converted space. If you do not know how the attic was designed, say so and ask what evaluation is needed.

The Building America Solution Center describes unvented attics as assemblies with their air, thermal, and moisture control boundaries at the roof. Visible spray foam alone is not a complete diagnosis. The contractor needs to understand the actual assembly and relevant design information. Ask whether an insulation or building-performance professional should participate before the roof's openings are changed.

Keep this question separate from the shingle selection. Choosing Owens Corning shingles does not decide how an existing attic should be ventilated. A reroof offers an opportunity to review the arrangement, but it should not trigger a routine change that ignores how the rest of the home works.

Request a plain written description of the intended approach so the installation crew has the same information as the person who inspected the attic.

2. Ask where replacement air will enter

For a vented attic, ask the contractor to identify the intake locations and evaluate whether the intended openings are usable. A soffit that looks perforated from outside does not tell you everything about the path behind it. Ask how the inspection addressed the full route.

Owens Corning's ventilation calculator is a manufacturer resource for planning ventilation. Ask the contractor to explain the assumptions and product information used for your house, along with the applicable requirements. A homeowner should not have to estimate those inputs from driveway photographs.

If the proposal includes intake changes, ask exactly where they will occur and whether soffit, insulation, or other work is included. If another trade is needed, name that responsibility in the scope. Keep the answer attached to the roof estimate so the ventilation work does not become an unassigned follow-up item.

3. Separate attic area from the length of the roof peak

Ask which attic spaces the contractor evaluated. A long ridge does not tell you whether an addition has a separate attic, whether an interior division interrupts the space, or whether another part of the roof needs a different solution.

Request a sketch showing the attic sections and proposed vent locations. It does not need to be a presentation-quality drawing. It needs labels that connect the roof work to rooms or sections you recognize, such as the main house, garage, and back addition.

If the contractor could not access a space, ask how that limitation affects the recommendation. A proposal can identify further investigation without pretending the whole assembly was observed. If an existing report or renovation drawing is available, provide it before the final scope is written.

Use the explanation to understand the proposed work rather than to calculate a vent count yourself. Product dimensions and usable vent area are different kinds of information; the contractor should specify the products and design basis.

4. Identify what happens to existing vents

Have the contractor list the current exhaust openings and describe which ones will stay, change, or be removed. Ask how the proposed arrangement was selected. If the roof has a mixture of ridge, box, gable, or powered vents, point that out for review without assuming that more openings must be better.

Also distinguish attic ventilation from ducts that serve equipment or exhaust fans. Ask the contractor to identify any duct or termination that another qualified trade needs to review. This avoids approving removal based on the appearance of a roof opening alone.

Request that abandoned openings and related repairs be addressed in the written scope. If the estimate includes only new ridge vent, ask whether it also includes the other work necessary for the proposed arrangement. Otherwise, the price may describe one component while leaving the overall change incomplete.

5. Define the expected result and how work will be checked

Tell the contractor what prompted your question: reroof planning, moisture concerns, a hot room, or an inspection report. Ask which observations support the ventilation recommendation and which concerns may involve insulation, air leakage, or the cooling system instead.

Avoid using an unsupported energy-savings percentage to justify the purchase. Ask what the work is intended to address and how the contractor will document its completion. If a comfort problem remains, request a sensible follow-up plan that recognizes the other systems involved.

Before closeout, ask for photographs and a record of the installed vent products and locations. Keep those details with the roof documents. They can help a future contractor understand the arrangement without guessing from the outside of the house.

Bring an attic information sheet

Write down known insulation changes, additions, past moisture concerns, and any inaccessible areas. Add the specific question you want answered, such as “Does the new ridge vent have a suitable intake arrangement?” Leave unknowns marked unknown.

Discuss that sheet with Brehm Roofing before finalizing your Gainesville roof replacement. Ask for a ventilation explanation that fits the house you have, including its renovation history.

The preparation plan should fit your property. A Gainesville home with a narrow driveway, a screened porch, and a home office needs different arrangements from a vacant house with open access. Use the appointment before installation to walk through the property and settle these details with the project contact.

1. Where vehicles will go

Ask which parts of the driveway need to remain clear and when deliveries may arrive. Move the vehicles you expect to use before equipment blocks their exit. Include a vehicle kept in the garage, a boat trailer, and any visitor parking you control.

If street parking or a shared access lane is involved, settle the permitted arrangement with the appropriate parties. Do not assume a neighbor's driveway or an open-looking space is available. Give the contractor a practical delivery route that preserves the access your household needs.

2. Where materials and debris containers will sit

Review proposed locations for materials, equipment, and disposal containers. Point out irrigation features, delicate pavers, low branches, and anything below the surface the crew should know about. Ask how surfaces will be protected and what limitations remain.

Confirm the planned removal of equipment after the work. If a container must remain overnight, ask how that affects access. A simple photograph with the staging area marked can help the salesperson, delivery team, and installation crew work from the same instructions instead of three different descriptions.

3. How people will enter and leave the house

Identify the entrance your family should use and the areas that will be restricted during work. Ask how the crew will communicate a temporary change if overhead work affects that route. Include accessibility needs in this conversation.

Think through deliveries, school pickup, visitors, and anyone who normally enters through a side gate. Tell household members about the agreed route before the crew arrives. Avoid sending someone through an active work area because the front door happens to be their normal entrance.

4. What to do with outdoor belongings

Ask which items should be moved away from the house. Patio furniture, planters, grills, toys, decorations, and equipment may be close to the work area. Identify anything too heavy or delicate for you to move safely and discuss assistance beforehand.

Point out a screened enclosure, pool area, or fragile landscaping. Ask what protection is planned and who handles any preparation that falls outside the roofing scope. Photographs of the property before work can document the starting condition and help settle questions about a particular surface afterward.

5. How children and pets will be accommodated

Plan for unfamiliar people, noise, open gates, and restricted outdoor areas. Decide whether children or pets will spend part of the day elsewhere. If they remain home, choose an arrangement that keeps them away from active work and deliveries.

Tell the project contact about gates that normally stay locked and pets that might approach workers. Make one household member responsible for checking the pet arrangement when the day starts. Do not rely on a busy crew to remember which animal might slip through an open door.

6. Which indoor belongings need attention

Ask what vibration and dust you should expect and which areas may need preparation. Review fragile wall hangings, loose shelf items, and belongings in an accessible attic storage area. Move or protect items only where you can do so safely.

Do not enter an attic with unsafe footing or expose yourself to heat or other hazards to cover stored belongings. Explain any access limitation to the contractor. If you have an existing ceiling crack or stain, photograph it before work and point it out during the preconstruction discussion.

7. Whether working from home is realistic

Describe your workday before deciding to remain in the house. Calls, recordings, focused work, and daytime sleep can be difficult to arrange around roof installation. Ask about the anticipated activity and plan another location if your schedule depends on quiet.

Also mention any household medical or accessibility needs that affect the day's arrangements. You only need to share the practical accommodation, not private medical details. Confirm whether anyone needs to be home for access or decisions so you can plan without assuming attendance is required all day.

8. Who can approve an unexpected change

Save the project contact's name and number. Confirm who can approve additional work, which communication method will be used, and what documentation you will receive. Name a backup contact if the primary decision maker may be unavailable.

Review the agreed process for concealed conditions before installation. If both owners want to approve a change, plan a way to reach both. Let the contractor know about meetings or travel that will make you unavailable so an ordinary project question does not become a prolonged interruption.

9. How schedule changes and closeout will be communicated

Ask when you should expect confirmation of the start date and how weather-related changes will be communicated. Gainesville homeowners can check the National Weather Service local forecast, but the contractor must assess the working conditions for the actual project.

Agree on the next update time if work changes. Also ask how the final walkthrough, cleanup questions, inspection status, and remaining documents will be handled. Keep the plan realistic for your house instead of treating another project's duration as a promise for yours.

Send one household preparation message

After the meeting, send the contractor a short note confirming parking, delivery space, the usable entrance, pet arrangements, and the approval contact. Ask them to correct anything you misunderstood. Share the same note with the adults in the household.

When arranging your project with Brehm Roofing, mention any driveway, enclosure, access, or scheduling concern early. Those details are easier to resolve before the delivery truck turns onto your street.

If water is near electrical equipment or a ceiling is sagging, stay away from that area and seek urgent professional help. Otherwise, document what you can see safely indoors. Avoid climbing onto a wet roof or entering an unsafe attic. The following are possible explanations to discuss with a roofer, not diagnoses you can make from a ceiling photograph.

1. Wind exposes an opening that ordinary rainfall does not reveal

Tell the roofer whether the leak appears during windy rain, steady vertical rainfall, or either condition. That distinction can help guide the inspection toward roof edges, exposed junctions, damaged roofing, or other locations the contractor needs to evaluate.

Record the room and the nearest exterior wall. Note which side of the house seemed to receive the rain, but label that as your observation rather than a measured wind direction. If you have an existing roof repair record, send it with the new information. A contractor investigating an intermittent leak needs the history as well as the current stain.

Owens Corning's storm-damage guidance notes that missing shingles and broken shingle seals can be relevant to wind damage, including damage that is difficult to see. Have a professional assess the roof; an intact-looking surface from the driveway cannot settle the question.

Avoid calling the roof “storm damaged” solely because the leak appeared during a storm. Report what happened and let the inspection establish the condition and potential causes.

2. Water collects at a drainage bottleneck

Ask the roofer to evaluate the path water takes across the affected roof section. A valley, a porch junction, or a roof area beneath an upper downspout may deserve attention. If you noticed gutter overflow from a safe indoor location, record where it occurred.

On a tree-lined Gainesville property, also mention recent debris buildup or a branch incident. You do not need to remove debris yourself to give the roofer useful context. A ground-level photo after conditions are safe can show the general location without exposing you to a fall.

The inspection should distinguish a drainage concern from a defect in the roof covering or flashing. Ask what evidence supports the proposed repair and whether a separate gutter service is needed. If both trades are involved, identify who checks the connection between their work.

Do not assume cleaning the gutters proves the leak is fixed. Keep a record of the cleaning date and the next rainfall observation. If water reappears, that record helps the contractor understand which possible explanation was addressed and which questions remain open.

3. A roof junction or penetration needs closer inspection

Ask the roofer to review the features above and around the affected room: plumbing vent pipes, skylights, chimneys, walls, and changes in roof shape. The contractor should explain which features are relevant rather than listing every component as a possible repair.

If a porch ceiling is wet where it joins the house, include the porch in the inspection request. If a stain is near a skylight, ask for the roof connection and the unit to be evaluated before authorizing replacement of either. A stain's location can help start the investigation without proving where water entered.

Tell the roofer about recent work by other trades. A new vent, satellite mount, solar service visit, or exterior renovation may provide a useful timeline. Describe the work without assuming the last contractor caused the leak.

Request photographs showing the suspected defect and its relationship to the surrounding roof. Before-and-after images of a small repair are more useful when a wider photograph explains where that repair was made. Keep the written scope as well, especially if the proposal excludes adjacent wall or siding work.

4. The stain has been attributed to the roof before the source is established

An interior stain deserves investigation even when its source is uncertain. Tell the contractor whether it changes only with rain or also appears during dry weather. Mention nearby plumbing, air-conditioning equipment, or recent interior work when relevant.

Ask what the inspector was able to observe and which areas were inaccessible. If the roof inspection does not establish a cause, ask what additional evaluation makes sense. That may involve another qualified trade. Ask for evidence of a roof source before repeating a patch above a ceiling stain.

Keep the original photographs before anyone paints, opens, or repairs the interior finish. If water entry has stopped, ask the responsible professional how drying and interior restoration should be handled. Cosmetic work should follow a plan for the underlying concern.

An honest report may identify a likely cause and recommend further investigation. Request that distinction in writing. “We found an opening at this location” and “we need to inspect this concealed area” give you different information about the next decision.

Keep a short rain-and-leak log

Use a phone note with the date, room, time water appeared, visible changes, and any safe photographs. Add whether the event involved wind, gutter overflow, or recent work. Record observations even if the stain stayed unchanged; that helps describe the intermittent pattern.

Do not wait for another storm to request help with active water entry. Send the existing log to Brehm Roofing's Gainesville roof repair team and ask for an inspection that addresses the leak history as well as the visible stain.

Brehm uses Owens Corning shingles for Gainesville roofing projects. When reviewing your proposal, keep the product selection and the warranty selection beside each other. You should be able to trace a verbal explanation to a named document and understand what you need to keep after installation. These questions help you make that review without relying on a large number printed on a brochure.

1. What is the complete name of the warranty in this proposal?

Ask the contractor to write the name in the estimate and supply the current document. If more than one option is available, request a separate explanation of each option and its price. Keep the version used for your decision.

Owens Corning's warranty page provides a starting point for reviewing and comparing its roofing warranties. Use the actual warranty applicable to the proposed installation for details. Ask the salesperson to identify where the document addresses the promises discussed during the appointment.

If the proposal says only “manufacturer warranty,” request more detail before comparing it with another offer. That clarification should identify what you are being offered without requiring you to guess from a contractor badge or a shingle sample.

2. Which products and installation conditions apply?

Ask which shingle, starter, hip and ridge, underlayment, and ventilation products belong to the quoted system. Have the contractor connect any eligibility requirements to that actual list. A generic diagram can help explain components, but your written scope should identify the products planned for your house.

If the estimate includes an enhanced warranty option, ask the contractor to confirm both its ability to offer that option and the project requirements. Keep the response with your proposal. Do not infer a particular warranty tier from the fact that a business installs the manufacturer's shingles.

This becomes especially useful when a product changes before installation. Ask whether the substitution changes eligibility, documentation, or the terms you reviewed. A written product revision should include any related warranty change so you can evaluate the complete proposal again.

3. What does each coverage period refer to?

Ask the contractor to explain the different time periods shown in the document. Write down what each period concerns, when it begins, and whether the remedy changes over time. Ask where the document defines any term you do not understand.

Avoid treating a long headline period as a promise that every future roof problem will be paid for in full. Read the provisions describing covered conditions, remedies, exclusions, and your responsibilities. If a statement during the sales conversation sounds broader than the document, ask the contractor to reconcile the difference before you decide.

Also ask whether the coverage being discussed applies to the type of ownership and building involved. A primary residence, rental property, or other ownership arrangement should be identified accurately. Give the contractor the actual situation rather than assuming one brochure example fits every project.

4. What workmanship coverage does the contractor provide?

Request the contractor's written workmanship terms alongside the manufacturer warranty. Ask who provides each promise and how you would report a concern. Make sure the contact information will still be usable after the sales appointment ends.

Ask the contractor to identify what its workmanship coverage includes, its duration, and any limitations. If a manufacturer option also discusses workmanship, have the contractor explain that document separately. The answers should make the responsibilities easier to follow, especially if a future concern involves both a roofing component and the way it was installed.

Do not rely on a workmanship period quoted in an old blog post. Use the terms included with your current signed proposal. Product offerings and business commitments can change, and the documents for your installation should carry the explanation you use to make a decision.

5. What happens if I sell the house or add equipment later?

If you expect to sell your Gainesville home, ask how the applicable warranty handles a transfer. Identify any required action, timing, documentation, or fee in the actual terms. Keep a note with your household records so the question is not rediscovered during a rushed closing.

Also disclose planned roof work by other trades. Solar equipment, a satellite mount, a skylight project, or changes connected with an addition deserve a conversation before someone alters the finished roof. Ask how to coordinate that work and which documents to retain.

You are not trying to predict every future repair. You are identifying foreseeable changes while the people responsible for the installation can explain them. Request answers specific to the selected warranty and the proposed modification rather than a blanket assurance about all future work.

6. What paperwork should I receive and keep?

Ask who handles any required registration and what confirmation you will receive. Record the completion date, installed product names, invoice, and the warranty documents that apply to your roof. Store a backup somewhere other than a single email inbox.

Before the project is closed, check the name, address, product description, and dates on the records. Ask how to correct an error and who can supply a missing document. It is easier to resolve these details while the installation is recent and the project contact has the file open.

Make a warranty reference card

Create one note with the warranty name, document location, contractor contact, registration status, and any transfer action described in the terms. Add the question “Who do I call first?” and record the answer. Keep this card with the full documents; it should help you find them, not replace them.

For a proposal using Owens Corning shingles, contact Brehm Roofing and ask to review the product scope and warranty documents together. Bring any plans to sell, rent, or add solar equipment to that discussion.

Decking repairs can be difficult to predict from a ground-level estimate because roofing materials conceal the surface beneath them. That uncertainty belongs in the preconstruction conversation. If your Gainesville reroof uncovers damaged wood near a former leak or porch connection, you should already know who will call, what information you will receive, and how you can approve necessary work.

1. Decide whether the proposed repair matches the documented condition

Ask the project contact to show both the damaged area and its location on the roof. A close-up can show a concern while leaving you unsure whether it is above the kitchen, garage, or back porch. Request a wider photograph and a short location description with it.

Then ask what the installer found. The explanation might concern deteriorated material, an unsuitable surface, or a condition that needs further evaluation. Ask the contractor to distinguish the visible finding from its suspected cause. A stained panel and a panel that cannot serve its intended purpose are different observations; the contractor should explain the recommendation for the material in front of them.

Clarify the repair boundary. Does the proposal replace individual panels, a strip at the eave, or a larger roof section? Ask why that boundary was selected and whether related components are affected. If the concern extends into framing, ask who will evaluate that separate issue and what additional authorization may be needed.

You can request documentation without going onto the roof. Stay outside the work area and use the photographs supplied by the crew. If you are away from home, have the project contact label the pictures rather than sending an unexplained sequence of images. Save the explanation with the change request so it remains understandable after the old material is gone.

2. Decide whether the price and authorization are clear enough

Before removal begins, read the decking allowance in the contract. Note whether it includes a quantity, a dollar allowance, or no replacement at all. Ask how unused allowances are treated and what happens when the actual work exceeds them. Different proposals may handle this differently.

When additional work is proposed, ask for the quantity, material, labor, and total price. Confirm the unit. A rate per sheet cannot be compared directly with a rate per square foot or linear foot. Ask whether removal, disposal, fastening, and any associated work are included in the quoted amount. Do not assume a familiar material name explains the whole charge.

A simple hypothetical shows why the detail matters. If a proposal includes some replacement wood, the change request should show which quantity uses that allowance and which quantity is additional. You should not need to reconstruct that calculation from a final invoice after the roof is finished.

Choose one person who can authorize changes, plus a backup if that person will be unavailable. Agree on the communication method and how written approval will be recorded. If both owners want to review added costs, arrange that before the crew is waiting for an answer.

Also discuss the contingency if you cannot be reached. The contract should explain the limits of any prior authorization and the approach to protecting the work. Avoid making that decision through rushed messages while you are driving or in a meeting. A clear approval process gives both sides a usable record of the agreed work.

3. Decide what documentation and follow-up you need before closeout

Ask for photographs after the repair and before the new roofing hides it. Request the same location labels used for the original findings. Paired photographs make it easier to understand what changed and keep the completed work associated with the correct part of the house.

Confirm how the contractor will address the condition connected with the damaged wood. If the concern was near a recurring leak, ask which part of the roof repair addresses water entry. If the cause remains uncertain, request that uncertainty in the project notes. Replacing visible material and explaining why it became damaged are separate parts of the discussion.

Ask the contractor which inspection or documentation requirements apply before covering the work. The Alachua County building permit page includes reroof inspection resources; your contractor should identify the authority and requirements for your actual address. Avoid assuming every Gainesville mailing address follows the same administrative process.

At closeout, compare the approved change with the final invoice. Check the location, quantity, and price, and keep the before-and-after photographs with both documents. If the repaired area affected an existing ceiling stain, ask how you should monitor that location and when interior repair can be considered. Do not use fresh paint as the test of whether the source was addressed.

Write this into your preconstruction notes

Use these prompts during the estimate discussion:

• What decking work does the base price include?
• What evidence will you send if additional repairs are proposed?
• What pricing unit and included labor will apply?
• Who can approve the work, and what is the backup contact?
• Which photographs and completion records will I receive?

Keep those answers somewhere you can open on your phone. Add the contractor's contact name so an unfamiliar number during the workday is easier to recognize.

If you are planning a reroof, ask Brehm Roofing about roof replacement in Gainesville and discuss the decking allowance before choosing an installation date. That conversation is easier while the existing roof is still in place.

For a Gainesville home with a main roof, an attached porch, and an older addition, even the phrase “full roof replacement” needs a boundary. Ask each contractor to mark the included roof sections on the same photograph or drawing. Then work through the written scope together. You should be able to explain what you are buying without translating roofing shorthand yourself.

1. The roof areas included in the price

Start with the house, garage, porches, and additions. Confirm which surfaces the contractor measured and which surfaces the estimate excludes. A low-slope porch might need a different roofing system and a separate scope.

Ask the contractor to distinguish measured roof area from material ordered for cuts and waste. Those quantities serve different purposes. If one estimate is much larger, ask where the difference comes from. A marked roof drawing can settle that conversation faster than debating a single square-foot figure. Keep the drawing with the estimate so a later revision has a clear starting point.

2. The exact shingle and accessory products

“Owens Corning architectural shingles” identifies a manufacturer and a broad type of product. Ask for the full product name and selected color. Then identify the starter shingles, hip and ridge shingles, and underlayment separately.

Brehm uses Owens Corning for asphalt shingle roofing in Gainesville. Your proposal should still identify the products for your particular house. If a substitution becomes necessary, ask for the new product details before approval. A color that looks similar in a brochure may belong to a different shingle line with different documentation.

3. Tear-off and disposal

Ask what the contractor expects to remove and how that expectation was established. Existing layers, an older repair, or roofing over an addition may affect the removal work. The estimate should explain how an unexpected condition will be handled.

Confirm whether disposal, hauling, and equipment removal are included. Ask where the container will sit and when it should leave. On a driveway used for daily school or work trips, that arrangement can matter as much as the first delivery time. Discuss access before equipment is parked where a vehicle needs to exit.

4. Decking repairs and additional charges

Roof decking is the surface beneath the roofing materials. Some of its condition may remain concealed until removal begins. Ask what wood replacement, if any, is included in the base price and how additional repairs will be documented.

Request the unit used for pricing, the labor included, and the approval process. “Wood extra” leaves too much unresolved. A clearer explanation identifies the material, the rate or pricing method, and who will contact you with photographs. Confirm whether trim, fascia, and structural repairs fall under separate items so one allowance does not appear to cover everything.

5. Flashing and roof penetrations

List the places where something passes through the roof or where the roof meets another surface. These may include plumbing pipes, a chimney, sidewalls, skylights, and a porch transition. Ask what happens at each location.

The useful distinction is whether a component will be replaced, retained after inspection, or excluded. A general sentence about “flashing as needed” makes comparison difficult. Ask for the scope to identify any wall or siding work necessary to complete a repair, including who performs it and whether finishing work is included. That avoids discovering a second trade requirement halfway through the project.

6. The ventilation assessment

A proposal that lists ridge vent should explain why that approach fits the house. Ask what attic areas were assessed, what intake is available, and whether an addition has a separate attic space.

You do not need to design the ventilation yourself. You need to know whether the contractor evaluated the existing arrangement and what the quoted work changes. Ask for the proposed vent locations on the roof drawing. If the home has spray foam at the roof deck, disclose it before the ventilation scope is finalized; that condition needs a specific review rather than a routine vent replacement decision.

7. Permit responsibilities and completion steps

Identify who handles the applicable permit and inspections, what fees the quote includes, and which office has jurisdiction over the address. Use the City of Gainesville building forms or Alachua County permit resources as starting points for the appropriate authority.

Also define completion. Installation, cleanup, an inspection, and final paperwork may happen at different times. Ask which milestones control invoicing and how remaining items will be recorded. Put any deadline that matters to your household into the discussion before signing.

8. The named warranties and exclusions

Request the manufacturer warranty by name and the contractor's workmanship coverage in writing. Ask what is included in this price and what, if anything, is optional. Keep the actual documents alongside the proposal.

Avoid comparing warranties by the biggest number in the sales presentation. Ask who handles a reported problem, what records you should retain, and which conditions or exclusions you should read. If a contractor describes an enhanced Owens Corning warranty, ask for the applicable eligibility requirements and confirmation for your installation. The manufacturer name alone does not establish the warranty included in your quote.

A comparison sheet you can use

Create a page with three columns: scope item, contractor A, and contractor B. Enter the eight items above. Write “not stated” wherever an estimate is silent; do not assume silence means included. Send each contractor the unanswered items and request a revised written scope.

Only compare final totals after the scope is clear. You may still choose different materials or coverage, but you will understand what explains the price difference. Bring that marked-up sheet to Brehm Roofing's contact team when you request an estimate for your Gainesville home.

This is the first post on the Brehm Roofing blog. It is a short one, mostly to say what this page is for.

Why we are writing

Most of the questions we hear on inspections are the same questions, asked by different homeowners in different neighborhoods. How long should a roof last here? What does a free inspection actually cover? What happens after a storm? Those answers do not fit on a service page, so they will live here.

What you can expect

• Plain-language posts from the people who inspect and build roofs in Gainesville, Ocala, The Villages and the surrounding communities.
• No sales pitch in the body of a post. If a topic calls for a roof inspection, we will say so, and the inspection is free.
• Honest answers, including the times a repair makes more sense than a replacement.

About the team behind it

Brehm Roofing & Restoration is a family-owned, Florida-licensed roofing contractor based in Gainesville and an Owens Corning Platinum Preferred Contractor. You can meet the team, read how a project runs from the first call to the handoff, or book a free roof inspection whenever you are ready.

Thanks for reading. New posts will show up on the blog page as they are published.

This Silver Springs Shores home in Ocala needed a full shingle replacement on a schedule that depended on price. The homeowners compared shingle and metal options, then stayed with architectural shingles.

We installed about 19 squares of Owens Corning Duration in Onyx Black with 3 starter bundles, 2 bundles of OC ProEdge hip and ridge, and new black drip edge throughout. Sales consultant Alex Lawrence helped plan the replacement in Silver Springs Shores.

We pulled the reroof permit for this job. View the finished project on our Silver Springs Shores Showcase.

Finished Owens Corning Duration Onyx Black roof in Silver Springs Shores, Ocala, FL.

Why Owens Corning Duration Onyx Black for a Silver Springs Shores reroof?

Owens Corning Duration in Onyx Black was the system chosen for this full Silver Springs Shores replacement after the homeowners compared shingle and metal.

They wanted ASAP timing depending on price and stayed with architectural shingles. Onyx Black is a dark multi-tone Duration color that fits a residential Ocala lot. About 19 squares covered this home, with 3 starter bundles and 2 ProEdge hip and ridge bundles finishing the peaks.

Sales consultant Alex Lawrence kept the scope on a retail replacement. Comparing both systems on the same tear-off scope helped them lock Duration Onyx Black without guessing at metal extras later.

Does a full Ocala reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This Silver Springs Shores job used new black drip edge throughout with the Onyx Black Duration field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Onyx Black Duration field on this Silver Springs Shores job in Ocala, FL.

What does a finished Duration Onyx Black field look like in Silver Springs Shores?

This job is a completed reroof with a clean Onyx Black Duration field, matching ProEdge on the ridges, and finished planes in Silver Springs Shores.

Ocala homes take Marion County heat, summer storms, and neighborhood tree cover. A Duration system with new black drip edge is built for that weather.

Finished Onyx Black Duration field and vent detail on the Silver Springs Shores job.

Project details

Detail This project

System / manufacturer Owens Corning Duration architectural shingles

Color Onyx Black

Squares About 19

Starter 3 bundles

Hip / ridge 2 bundles OC ProEdge

Drip edge New black (always new on a full reroof)

Project type Full roof replacement

City Silver Springs Shores / Ocala, FL

Sales consultant Alex Lawrence

Permit Permit pulled

FAQs

Is Onyx Black a good color choice for Silver Springs Shores homes?

Onyx Black is a dark multi-tone Duration color that works well on many Ocala elevations. Color preference is personal, so walk sample boards on your elevation with your sales consultant before you lock the order.

Should I compare shingle and metal before I sign a Silver Springs Shores quote?

Yes when both options matter to you. This homeowner compared shingle and metal, wanted ASAP timing depending on price, then stayed with Duration Onyx Black. Ask for the same tear-off scope, drip edge plan, and start window on both quotes so the numbers stay apples to apples.

What should I ask about starter and ProEdge on a Duration quote?

Ask whether the quote includes starter and manufacturer hip and ridge as separate line items. This Silver Springs Shores job used 3 starter bundles and 2 ProEdge bundles with the Onyx Black field. Those pieces are part of a complete system, not optional add-ons you should have to chase later.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this Silver Springs Shores job is our Ocala location at 1729 E Silver Springs Blvd Suite 5.

Get a Free Estimate if you want to talk through an Owens Corning Duration Onyx Black reroof in Silver Springs Shores or greater Ocala.

Signing a reroof contract in The Villages, FL is smoother when you know which timeline and paperwork questions to ask before the dumpster shows up. These five contract and timeline checks help homeowners in The Villages line up start dates, permit timing, material locks, and change-order rules in writing.

We recently finished a reroof in the Village of Moncks Corner near Lake Sumter Landing in The Villages, FL: about 40 squares of Owens Corning Duration in Williamsburg Gray with new white drip edge. That finished project is the local proof behind a few of the points below. View the Moncks Corner Showcase.

Sales consultant Turner Pillsbury helped plan that age-related replacement for a homeowner who stayed with shingles after nearly 19 years of service and completed a third and final inspection. Use these questions early so your Villages contract matches the calendar you actually need.

Finished Owens Corning Duration Williamsburg Gray roof in the Village of Moncks Corner, The Villages, FL.

1. Does the contract name a clear start window after the permit?

Ask for a written start window that begins after the reroof permit is approved, not a vague promise to begin sometime this season.

Villages jobs often move through HOA notice, material staging, and county or city permit timing before tear-off. If the contract only says ASAP with no permit trigger, ask how many business days after approval the crew can begin.

2. Are materials, color, and drip edge locked in writing before day one?

Yes. Your Villages contract should name the manufacturer, product line, color, squares, starter, hip and ridge, and new drip edge so nothing is left to a verbal handshake.

On the Moncks Corner job we installed about 40 squares of Owens Corning Duration in Williamsburg Gray with 4 starter bundles, 9 ProEdge hip and ridge bundles, and new white drip edge. Black boots, vents, and paint finished the roof. Those line items should appear in the contract before the tear-off date, not as a surprise on the truck.

Finished Williamsburg Gray Duration field with black vents on the Moncks Corner job in The Villages, FL.

3. How does the contract handle weather delays and rain days?

Confirm how rain days, lightning holds, and decking discoveries shift the finish date without changing your price for the original scope.

Central Florida summer weather can pause a one-day plan. Ask whether the contract keeps the same crew returning the next workable day and whether temporary dry-in is included if a storm interrupts mid-tear-off.

4. Who pulls the permit, and who schedules the final inspection?

Put the permit puller and inspection scheduler in the contract so you are not left calling the building department yourself after the old roof is gone.

The Moncks Corner job was an age-related replacement, and it followed a third and final inspection before the install. Your Villages paperwork should say who files the reroof permit, who meets the inspector, and what happens if a re-inspection is needed.

Finished Williamsburg Gray Duration ridge and field on the Moncks Corner / Lake Sumter Landing job.

5. What change orders are allowed after the color and scope are signed?

Ask which extras require a signed change order, how decking replacement is priced per sheet, and whether color changes after materials ship are allowed at all.

Homeowners in The Villages often lock a color like Williamsburg Gray early because HOA notice and material staging take time. The Moncks Corner homeowner stayed with shingles after nearly 19 years of service. Once Duration Williamsburg Gray is on order, a late color swap can delay the start window you just negotiated. Get the change-order rules in writing before you sign.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for Moncks Corner and greater The Villages is our Villages location at 561 Fieldcrest Dr #1.

Get a Free Estimate if you want to walk a Villages reroof contract and timeline before you sign.

This northwest Gainesville home needed a full shingle replacement on a roughly 13-year roof after hail damage. The homeowner wanted to stay with shingles, and insurance plus other roofers had already inspected the existing system.

We installed about 32 squares of Owens Corning Oakridge in Estate Gray with 10 rolls of MFM SA starter, 5 bundles of OC ProEdge hip and ridge, ridge vent, ice and water, and new brown drip edge throughout. Sales consultant Mike Abadin walked the project in northwest Gainesville.

We pulled the reroof permit for this job. View the finished project on our northwest Gainesville Showcase.

Finished Owens Corning Oakridge Estate Gray roof in northwest Gainesville, FL.

Why Owens Corning Oakridge Estate Gray for a northwest Gainesville reroof?

Owens Corning Oakridge in Estate Gray was the system chosen for this full northwest Gainesville replacement on a roughly 13-year shingle roof.

The homeowner wanted to stay with architectural shingles after hail damage and prior inspections. Estate Gray is a multi-tone Oakridge color that fits a residential Gainesville lot. About 32 squares covered this home, with 10 rolls of MFM SA starter and 5 ProEdge hip and ridge bundles finishing the peaks, plus ridge vent and ice and water.

Sales consultant Mike Abadin kept the scope on a retail replacement timed for this month. Hail damage was the reason to replace rather than waiting for another storm season on aging shingles.

Does a full Gainesville reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This northwest Gainesville job used new brown drip edge throughout with the Estate Gray Oakridge field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Estate Gray Oakridge ridge and field on a northwest Gainesville roof.

What does a finished Oakridge Estate Gray field look like in northwest Gainesville?

This job is a completed reroof with a clean Estate Gray Oakridge field, matching ProEdge on the ridges, ridge vent, and finished planes in northwest Gainesville.

Gainesville homes take Alachua County heat, summer storms, and neighborhood tree cover. An Oakridge system with new brown drip edge is built for that weather on a residential lot in Gainesville.

Finished Estate Gray field and ridge on this northwest Gainesville roof.

Project details

Detail This project

System / manufacturer Owens Corning Oakridge architectural shingles

Color Estate Gray

Squares About 32

Starter 10 rolls MFM SA starter

Hip / ridge 5 bundles OC ProEdge

Ventilation / underlayment Ridge vent; ice and water

Drip edge New brown (always new on a full reroof)

Project type Full roof replacement

City Northwest Gainesville, FL

Sales consultant Mike Abadin

Permit Permit pulled

FAQs

Is Estate Gray a good color choice for northwest Gainesville homes?

Estate Gray is a multi-tone Oakridge color that works well on many Gainesville elevations. Color preference is personal, so walk sample boards on your elevation with your sales consultant before you lock the order.

Should I replace after hail even if other roofers already inspected?

Often yes when the roof is around 13 years old and hail damage is confirmed. This homeowner had hail damage with insurance and other roofers inspecting, then chose a full Oakridge Estate Gray replacement. Ask your sales consultant to review photos and scope before another storm season.

What should I ask about starter, ridge vent, and ice and water on an Oakridge quote?

Ask whether the quote includes self-adhered starter, manufacturer hip and ridge, ridge vent, and ice and water where the plan calls for them. This northwest Gainesville job used 10 rolls of MFM SA starter, 5 ProEdge bundles, ridge vent, and ice and water with the Estate Gray field. Those pieces are part of a complete system, not optional add-ons you should have to chase later.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this northwest Gainesville job is our Gainesville location at 1344 NW 121st Way.

Get a Free Estimate if you want to talk through an Owens Corning Oakridge Estate Gray reroof in northwest Gainesville.

Storm season in Silver Springs Shores, Ocala, FL is easier to manage when you know which roof checks to run before the next round of wind and rain. These five storm-season roof checks help homeowners in Silver Springs Shores catch lifted shingles, wet attic signs, weak edge metal, and timing gaps early. This is not a hurricane forecast and it is not a price list.

We recently finished a reroof in Silver Springs Shores, Ocala: about 19 squares of Owens Corning Duration in Onyx Black with new black drip edge. That finished project is the local proof behind a few of the points below. View the Silver Springs Shores Showcase.

Sales consultant Alex Lawrence helped plan that replacement for a homeowner who wanted ASAP timing depending on price, compared shingle and metal, and stayed with shingles. Use these checks before peak storm weeks so you are not guessing from the driveway after the first hard rain.

Finished Owens Corning Duration Onyx Black roof in Silver Springs Shores, Ocala, FL.

1. Are any shingles lifted, cracked, or missing after the last wind event?

Walk the yard and look from ground level for tabs that sit up, cracked ridges, or bare spots after wind, then call for a roof check if anything looks off.

Storm-season damage often shows first along ridges and field edges. The Silver Springs Shores roof is a finished Duration Onyx Black system, so you can see what clean field and ridge lines look like when a roof is new. If your shingles look curled or opened after a storm, get photos before the next rain.

2. Do you see attic or ceiling stains after wind-driven rain?

Yes. Check the attic deck and ceiling corners after a hard rain for damp wood, dark stains, or dripping insulation that point to an active leak path.

Silver Springs Shores homes take Marion County wind and summer downpours. A stain that shows up only after storms is a timing clue, not something to ignore until dry season. Note the room and the weather date so your sales consultant can match the leak to the roof plane.

Finished Onyx Black Duration field on the Silver Springs Shores job in Ocala, FL.

3. Is drip edge and edge metal still tight before hurricane weeks?

Yes. Confirm drip edge and edge metal are secure and not rusted or bent before peak hurricane weeks, because weak edges are where wind lifts start.

On every full Brehm roof replacement we install new drip edge with the new shingles. The Silver Springs Shores job used new black drip edge with the Onyx Black Duration field. If another bid reuses old drip edge on a full reroof, that is not an apples-to-apples storm-ready plan. See the Showcase.

4. Have you photographed the roof age and condition before the next named storm?

Yes. Take clear photos of the field, ridges, and vents now so you have a dated baseline if wind or hail hits later in the season.

Homeowners who compared shingle and metal like the Silver Springs Shores job still needed a clear record of what was on the house before work started. A dated photo set helps your contractor and any insurance review stay specific. Keep shots from the ground and any safe elevated views you already have.

Finished Onyx Black Duration ridge and field on the Silver Springs Shores job.

5. Do you know your reroof timeline if storm damage is confirmed?

Ask which company pulls the permit, how material lead times work, and how soon a crew can start once the scope is approved.

The Silver Springs Shores homeowners wanted ASAP timing depending on price and stayed with shingles after comparing metal. ASAP only works when permit and material windows are written into the plan. Put start windows on the quote so a low number that cannot start for weeks does not beat a ready crew by surprise.

Nearby project

Silver Springs Shores, Ocala, FL. About 19 squares of Owens Corning Duration Onyx Black, 3 starter, 2 ProEdge, new black drip edge. Sales: Alex Lawrence. See the Showcase.

FAQs

Can I wait until after hurricane season to check my Silver Springs Shores roof?

No. Run these five checks before peak weeks so lifted shingles or attic stains are found while you still have options. Waiting until after the season often means living with a known leak path through more storms.

Does a new Duration roof help with storm-season readiness in Ocala?

A new Owens Corning Duration system with new drip edge gives you a clean field, ridge, and edge metal baseline. The Silver Springs Shores job used Duration Onyx Black with new black drip edge. Ask your sales consultant whether repair or full replacement fits the damage you found.

Where is the nearest Brehm office for Silver Springs Shores?

The nearest office for Silver Springs Shores and greater Ocala is our Ocala location at 1729 E Silver Springs Blvd Suite 5. Call 352-664-8887 to schedule a quote walk.

Brehm Roofing provides residential roof replacements throughout Ocala, Gainesville, The Villages, Minneola, and nearby North Central Florida communities.

Get a Free Estimate if you want help with storm-season roof checks or a Duration Onyx Black reroof in Silver Springs Shores or greater Ocala.

This University Park home near the University of Florida in Gainesville, FL needed a full shingle replacement due to age on a roughly 22-plus-year roof. The homeowner looked at metal and stayed with architectural shingles.

We installed about 29 squares of Owens Corning Duration in Harbor Blue with 3 starter bundles, 8 bundles of OC ProEdge hip and ridge, Titanium PSU30 underlayment, and new white drip edge throughout. Sales consultant Alex Lawrence walked the project in University Park.

We pulled the permit for this job. View the finished project on our University Park Showcase.

Finished Owens Corning Duration Harbor Blue roof in University Park, Gainesville, FL.

Why Owens Corning Duration Harbor Blue for an age-related University Park reroof?

Owens Corning Duration in Harbor Blue was the system chosen for this full University Park replacement after the homeowner called for a roof replacement due to age.

A roughly 22-plus-year shingle roof is past its comfortable service life in Gainesville heat and storms. Duration Harbor Blue is a cool multi-tone architectural shingle that fits a residential University Park lot near UF. About 29 squares covered this home, with 3 starter bundles and 8 ProEdge hip and ridge bundles finishing the peaks.

Sales consultant Alex Lawrence scoped the work. The homeowner looked at metal, then stayed with a new Duration Harbor Blue shingle system on a timeline of the next 30 days.

Does a full Gainesville reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This University Park job used new white drip edge throughout with the Harbor Blue Duration field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Harbor Blue Duration field and chimney cricket on a University Park reroof in Gainesville, FL.

What does a finished Duration Harbor Blue field look like in University Park?

This is a completed reroof with a clean Harbor Blue Duration field, matching ProEdge on the ridges, and finished planes near UF.

Gainesville homes take Alachua-area heat, summer storms, and neighborhood tree cover. A Duration system with Titanium PSU30 underlayment and new white drip edge is built for that weather on a residential lot in University Park.

Finished Harbor Blue field, ridge, and chimney flashing on the University Park reroof.

Project details

Detail This project

System / manufacturer Owens Corning Duration architectural shingles

Color Harbor Blue

Squares About 29

Starter 3 bundles OC Starter Shingle

Hip / ridge 8 bundles OC ProEdge

Underlayment Titanium PSU30 peel and stick

Drip edge New white (always new on a full reroof)

Project type Full roof replacement

City University Park, Gainesville, FL

Nearby landmarks UF

Sales consultant Alex Lawrence

Permit Permit pulled

FAQs

Is age alone a reason to replace a University Park shingle roof?

Often yes when the roof is past about 20 years and the homeowner is planning ahead rather than waiting on a leak. This University Park job was an age replacement on a roughly 22-plus-year shingle roof. Ask your sales consultant to walk the field and say whether a patch or a full system makes sense.

Can I look at metal and still choose Duration Harbor Blue?

Yes. Many Gainesville homeowners compare metal and shingle before locking the order. This University Park homeowner looked at metal and stayed with Owens Corning Duration Harbor Blue. Walk sample boards on your elevation with your sales consultant before you decide.

What should I ask about underlayment and drip edge on a Duration quote?

Ask whether the quote includes peel-and-stick underlayment and new drip edge with the field color plan. This University Park job used Titanium PSU30 underlayment and new white drip edge with the Harbor Blue Duration field. Those pieces are part of a complete system, not optional add-ons you should have to chase later.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this University Park job is our Gainesville location at 1344 NW 121st Way.

Get a Free Estimate if you want to talk through an Owens Corning Duration Harbor Blue reroof in University Park or greater Gainesville.

Metal roofs are a common question for Mount Dora, FL homeowners who want a system that handles Lake County heat and storms. These five answers cover metal versus shingle, drip edge, Lake County permits, mill finish Ultra Rib look, and install pacing. This is contractor guidance tied to a real nearby Brehm project, not a price list.

We recently finished a real metal reroof in Mount Dora, FL: 26g Ultra Rib mill finish metal with new drip edge throughout after storm damage that left a hole through a bedroom. That finished project is the local proof behind a few of the points below. View the Mount Dora metal Showcase or the full case study.

Sales consultant Alex Lawrence walked that Mount Dora metal replacement. We pulled the Lake County reroof permit for this job. Use these five questions early when you are comparing metal and shingle in Mount Dora.

Finished 26g Ultra Rib mill finish metal roof in Mount Dora, FL.

1. Is metal a better choice than shingle for Mount Dora heat and storms?

It depends on the home, the budget, and what look you want, but metal is a strong option for Mount Dora homeowners who want a long-lasting panel system under Lake County sun and rain.

Shingle still fits many residential streets in Mount Dora. Metal shines when the homeowner wants a ribbed panel field and is ready for a full tear-off. This job used 26g Ultra Rib mill finish metal after storm damage on a 2001 asphalt roof. Ask your sales consultant to walk both systems on your elevation before you lock the order.

2. Does a full Mount Dora metal reroof include new drip edge?

Yes. On every full Brehm roof replacement we install new drip edge with the new roof system, including metal jobs in Mount Dora.

This job used new drip edge throughout with the Ultra Rib panels. Edge metal protects the deck where water leaves the roof. We never reuse old drip edge on a full reroof. Confirm drip edge and fascia details on your quote so the metal field and eave line finish together.

Finished Ultra Rib mill finish metal field with box vents on a Mount Dora, FL reroof.

3. Do I need a Lake County permit for a Mount Dora metal reroof?

Yes. A full metal reroof in Mount Dora typically needs a Lake County reroof permit before tear-off starts.

We pulled the Lake County reroof permit for this 26g Ultra Rib mill finish replacement. Your sales consultant should say who pulls the permit and when inspections land. Do not start a full tear-off without the permit path clear.

4. What does mill finish Ultra Rib metal look like on a Mount Dora home?

Mill finish Ultra Rib is a ribbed metal panel left in its natural silver tone rather than a painted color coat on the field.

On this job, 26g Ultra Rib mill finish replaced damaged asphalt and closed a storm hole that went through a bedroom. The finished field reads bright and clean against Mount Dora tree cover. If you want a painted color instead, say so early so the panel order matches the elevation. See the Showcase.

Finished mill finish Ultra Rib metal elevation on a Mount Dora, FL reroof.

5. Can a Mount Dora metal roof finish in one day?

Sometimes, but metal panel installs often need more than one crew day depending on size, access, and deck work.

Ask your sales consultant for a day plan based on your square footage, steepness, and staging room. Weather and soft decking can stretch any schedule. A clear plan beats guessing when Lake County storms roll through Mount Dora.

Nearby project proof

Mount Dora, FL. 26g Ultra Rib mill finish metal, new drip edge throughout, Lake County reroof permit. Sales: Alex Lawrence. See the Showcase · Read the case study.

FAQs

Can storm damage with a hole through a bedroom force a full Mount Dora metal reroof?

Often yes. The homeowner on our Mount Dora job had storm damage with a hole through a bedroom on a 2001 roof and chose a full 26g Ultra Rib mill finish metal replacement instead of a patch. A bedroom leak that size usually means the system is done.

Where is the nearest Brehm office for Mount Dora?

Our Minneola office is at 506 S Hwy 27, Minneola, FL. We handle residential roof replacements throughout Mount Dora, Minneola, Clermont, Groveland, and nearby Lake County communities. Call 352-664-8887 to schedule a quote walk.

Should I compare metal and shingle quotes side by side?

Yes. Ask for the same scope on both: tear-off, underlayment, drip edge, vents, and permit. Sales consultants like Alex Lawrence can walk Ultra Rib mill finish against a Duration or Oakridge shingle option so you see cost and look differences clearly.

Brehm Roofing provides residential roof replacements throughout Ocala, Gainesville, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for Mount Dora work is our Minneola location at 506 S Hwy 27.

Get a Free Estimate if you want to talk through a 26g Ultra Rib mill finish metal reroof in Mount Dora or greater Lake County.

This Hamilton Heights home in west Gainesville, FL needed a full shingle replacement after a tree fell through the roof. The project came in as a BNI referral from Best Restoration, and the homeowner stayed with architectural shingles.

We installed about 38 squares of Owens Corning Duration in Onyx Black with 11 rolls of MFM SA starter, 7 bundles of OC ProEdge hip and ridge, and new black drip edge throughout. Sales consultant Alex Lawrence walked the project in Hamilton Heights.

We pulled the reroof permit for this job. View the finished project on our Hamilton Heights Showcase.

Finished Owens Corning Duration Onyx Black roof in Hamilton Heights, Gainesville, FL.

Why Owens Corning Duration Onyx Black after a tree fell through the roof?

Owens Corning Duration in Onyx Black was the system chosen for this full Hamilton Heights replacement after storm-related tree damage opened the old roof.

A tree through the roof is not a patch-and-hope job when the deck and field are compromised. Duration Onyx Black is a dark multi-tone architectural shingle that fits a residential west Gainesville lot. About 38 squares covered this home, with 11 rolls of MFM SA starter and 7 ProEdge hip and ridge bundles finishing the peaks.

Sales consultant Alex Lawrence scoped the work from a BNI referral through Best Restoration. That path kept the homeowner moving from damage to a planned full reroof instead of a temporary cover that would not last.

Does a full Gainesville reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This Hamilton Heights job used new black drip edge throughout with the Onyx Black Duration field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Onyx Black Duration ridge and field on this Hamilton Heights job in Gainesville, FL.

What does a finished Duration Onyx Black field look like in Hamilton Heights?

This is a completed reroof with a clean Onyx Black Duration field and matching ProEdge on the ridges.

Gainesville homes take Alachua County heat, summer storms, and neighborhood tree cover. A Duration system with new black drip edge is built for that weather on a residential lot in Gainesville.

Finished Onyx Black field and ridge on the Hamilton Heights job.

Project details

Detail This project

System / manufacturer Owens Corning Duration architectural shingles

Color Onyx Black

Squares About 38

Starter 11 rolls MFM SA starter

Hip / ridge 7 bundles OC ProEdge

Drip edge New black (always new on a full reroof)

Project type Full roof replacement

City Hamilton Heights, Gainesville, FL

Sales consultant Alex Lawrence

Lead source BNI referral from Best Restoration

Permit Permit pulled

FAQs

Can a tree through the roof be repaired instead of replaced?

Sometimes a small puncture can be patched, but when a tree opens a large section of field and deck, a full reroof is usually the cleaner path. This Hamilton Heights job was a full Duration Onyx Black replacement after tree damage, not a spot repair. Ask your sales consultant to walk the deck and say whether a patch or a full system makes sense.

Is Onyx Black a good color choice for west Gainesville homes?

Onyx Black is a dark multi-tone Duration color that works well on light stucco and tree-covered Gainesville lots like this Hamilton Heights home. Color preference is personal, so walk sample boards on your elevation with your sales consultant before you lock the order.

What should I ask about starter and hip or ridge on a Duration quote?

Ask whether the quote includes self-adhered starter and manufacturer hip and ridge that match the field color. This Hamilton Heights job used 11 rolls of MFM SA starter and 7 ProEdge bundles with the Onyx Black field. Those finishing pieces are part of a complete Duration system, not optional add-ons you should have to chase later.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this Hamilton Heights job is our Gainesville location at 1344 NW 121st Way.

Get a Free Estimate if you want to talk through an Owens Corning Duration Onyx Black reroof in Hamilton Heights or greater Gainesville.

One-day reroofs are common for Del Webb Stone Creek homeowners in Ocala, FL who want the tear-off and new shingles done while they are still living in the house. These five questions help Stone Creek residents plan crew day, materials, drip edge, and access before the dumpster rolls in. This is not a guarantee that every Stone Creek roof finishes in one day, and it is not a price list.

We recently finished a reroof in Del Webb Stone Creek, Ocala, near the community golf course: about 48 squares of Owens Corning Duration in Driftwood with new brown drip edge. That finished project is the local proof behind a few of the points below. View the Stone Creek Showcase.

Sales consultant Alex Lawrence helped plan that replacement for a homeowner with a roughly 14-year shingle roof who started from a website estimate and compared quotes. Use these one-day questions early so crew day stays simple for you and your neighbors.

Finished Owens Corning Duration Driftwood roof in Del Webb Stone Creek, Ocala, FL near the community golf course.

1. Can most Stone Creek homes finish a shingle reroof in one day?

Yes. Many Del Webb Stone Creek homes with a clear material stack and open access can tear off and install in a single crew day when weather holds.

Square count, steepness, and deck repairs still matter. The Stone Creek job used about 48 squares of Duration Driftwood. Ask your sales consultant whether your home fits a one-day plan or needs a second day for deck work.

2. Are materials staged on site before the tear-off starts?

Yes. A one-day Stone Creek reroof works best when shingles, starter, hip and ridge, and drip edge are on the ground before the old roof comes off.

The Stone Creek job used about 48 squares of Owens Corning Duration Driftwood, 3 starter bundles, and 13 ProEdge hip and ridge bundles. If those pieces are not staged, the crew day stretches. Confirm delivery timing with your sales consultant the day before.

Finished Driftwood Duration ridge and field on the Del Webb Stone Creek job in Ocala, FL.

3. Is new drip edge included on every full one-day reroof?

Yes. On every full Brehm roof replacement we install new drip edge with the new shingles, including one-day jobs in Stone Creek.

The Stone Creek job used new brown drip edge with the Driftwood Duration field. Edge metal protects the deck where water leaves the roof. We never reuse old drip edge on a full reroof, even when the crew is racing daylight.

4. What should I clear so the crew can move fast on install day?

Clear driveway space for the dumpster and material delivery, move patio furniture and grills away from eaves, and keep pets inside while tear-off is noisy.

Stone Creek streets and golf-community lots leave limited staging room. A clear driveway and open eaves keep a one-day Duration install on schedule. Ask your sales consultant for a short day-of checklist the night before.

Finished Driftwood Duration field on the Del Webb Stone Creek job.

5. How do weather and deck surprises change a one-day plan?

Rain windows and soft decking can push finishing to a second day even when the plan started as one day.

Ocala summer storms and older deck boards are the usual reasons. Your sales consultant should say how the crew protects an open roof and when a second day is called. A clear plan beats guessing when clouds build over Stone Creek. See the Showcase.

Nearby project

Del Webb Stone Creek, Ocala, FL, near the community golf course. About 48 squares of Owens Corning Duration Driftwood, 3 starter, 13 ProEdge, new brown drip edge. Sales: Alex Lawrence. See the Showcase.

FAQs

Do I have to leave the house during a one-day Stone Creek reroof?

Most homeowners stay home. Expect noise, vibration, and limited driveway access while the crew tears off and installs. Plan indoor work or errands for the loudest mid-day hours if you want a quieter stretch.

Can Brehm plan a one-day Duration Driftwood reroof in Stone Creek?

Yes. Sales consultants like Alex Lawrence routinely size Stone Creek homes for a same-day tear-off and install when materials and access line up. Bring your square estimate and access photos so the day plan is realistic.

Where is the nearest Brehm office for Del Webb Stone Creek?

The nearest office for Del Webb Stone Creek and greater Ocala is our Ocala location at 1729 E Silver Springs Blvd Suite 5. Call 352-664-8887 to schedule a quote walk.

Brehm Roofing provides residential roof replacements throughout Ocala, Gainesville, The Villages, Minneola, and nearby North Central Florida communities.

Get a Free Estimate if you want help planning a one-day Duration Driftwood reroof in Del Webb Stone Creek or greater Ocala.

This Blues Creek home in Gainesville needed a full shingle replacement on a roof from around 2011. The homeowner wanted to stay with shingles and was not in a rush.

We installed about 40 squares of Owens Corning Duration in Desert Rose with 10 rolls of MFM SA starter, 7 bundles of OC ProEdge hip and ridge, and new white drip edge throughout. Sales consultant Mike Abadin walked the project in Blues Creek.

We pulled the reroof permit for this job. View the finished project on our Blues Creek Showcase.

Finished Owens Corning Duration Desert Rose roof in Blues Creek, Gainesville, FL.

Why Owens Corning Duration Desert Rose for a Blues Creek reroof?

Owens Corning Duration in Desert Rose was the system chosen for this full Blues Creek replacement on a roof from around 2011.

The homeowner wanted to stay with architectural shingles rather than switching products. Desert Rose is a warm multi-tone Duration color that fits a residential Gainesville lot. About 40 squares covered this home, with 10 rolls of MFM SA starter and 7 ProEdge hip and ridge bundles finishing the peaks.

Sales consultant Mike Abadin kept the scope on a planned retail replacement with no rush on the timeline. Age alone was enough reason to replace the system instead of waiting for a leak or a denial letter.

Does a full Gainesville reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This Blues Creek job used new white drip edge throughout with the Desert Rose Duration field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Desert Rose Duration ridge and field on this Blues Creek roof in Gainesville, FL.

What does a finished Duration Desert Rose field look like in Blues Creek?

This job is a completed reroof with a clean Desert Rose Duration field, matching ProEdge on the ridges, and finished roof planes.

Gainesville homes take Alachua County heat, summer storms, and neighborhood tree cover. A Duration system with new white drip edge is built for that weather on a residential lot like this one.

Finished Desert Rose field and ridge on this Blues Creek roof.

Project details

Detail This project

System / manufacturer Owens Corning Duration architectural shingles

Color Desert Rose

Squares About 40

Starter 10 rolls MFM SA starter

Hip / ridge 7 bundles OC ProEdge

Drip edge New white (always new on a full reroof)

Project type Full roof replacement

City Blues Creek, Gainesville, FL

Sales consultant Mike Abadin

Permit Permit pulled

FAQs

Is Desert Rose a good color choice for Blues Creek homes?

Desert Rose is a warm multi-tone Duration color that works well on light stucco and tree-covered Gainesville lots like this Blues Creek home. Color preference is personal, so walk sample boards on your elevation with your sales consultant before you lock the order.

Do I need to wait for storm damage before replacing a ~2011 roof?

No. Many Blues Creek and greater Gainesville homeowners replace on age and condition. This was a planned reroof with no rush. Ask your sales consultant whether a planned Duration replacement fits your timeline better than waiting for damage.

What should I ask about starter and hip or ridge on a Duration quote?

Ask whether the quote includes self-adhered starter and manufacturer hip and ridge that match the field color. This Blues Creek job used 10 rolls of MFM SA starter and 7 ProEdge bundles with the Desert Rose field. Those finishing pieces are part of a complete Duration system, not optional add-ons you should have to chase later.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this Blues Creek job is our Gainesville location at 1344 NW 121st Way.

Get a Free Estimate if you want to talk through an Owens Corning Duration Desert Rose reroof in Blues Creek or greater Gainesville.

Comparing roof quotes in Silver Springs Shores, Ocala, FL is easier when you know which line items to check before you sign. These five quote-comparison checks help homeowners line up materials, drip edge, timing, and paperwork across contractors. This is not a price list and it is not a guarantee that every Ocala quote will use the same format.

We recently finished a reroof in Silver Springs Shores, Ocala: about 19 squares of Owens Corning Duration in Onyx Black with new black drip edge. That finished project is the local proof behind a few of the points below. View the Silver Springs Shores Showcase.

Sales consultant Alex Lawrence helped plan that replacement for a homeowner who wanted ASAP timing depending on price, compared shingle and metal, and stayed with shingles. Use these checks early so your quotes are apples to apples before the dumpster arrives.

Finished Owens Corning Duration Onyx Black roof in Silver Springs Shores, Ocala, FL.

1. Does every quote name the same shingle system and color?

Ask each contractor to write the manufacturer, product line, and color on the quote so you are not comparing a budget shingle to a Duration system by accident.

On the Silver Springs Shores job we installed Owens Corning Duration in Onyx Black. If one quote says Duration Onyx Black and another only says architectural black, press for the exact product line before you pick the lower number.

2. Are starter, hip and ridge, and squares listed as separate line items?

Yes. A clear Silver Springs Shores quote should show field squares plus starter and hip or ridge, not a single lump sum that hides finishing materials.

The Silver Springs Shores job used about 19 squares of Duration Onyx Black, 3 starter, and 2 ProEdge hip and ridge. Those numbers matter when you compare bids. If a quote skips starter or ridge, ask whether they are included or whether you will get a change order later.

Finished Onyx Black Duration field with new black drip edge on the Silver Springs Shores job in Ocala, FL.

3. Is new drip edge included on every full reroof quote?

Yes. On every full Brehm roof replacement we install new drip edge with the new shingles, and your quote should say so in writing.

The Silver Springs Shores job used new black drip edge with the Onyx Black Duration field. Edge metal protects the deck where water leaves the roof. We never reuse old drip edge on a full reroof. If another bid reuses existing drip edge, that is not an apples-to-apples comparison.

4. Did you compare shingle vs metal on the same scope and timeline?

Ask for side-by-side shingle and metal options only when both quotes use the same tear-off scope, drip edge plan, and start window.

The Silver Springs Shores homeowners compared shingle and metal, wanted ASAP timing depending on price, and stayed with shingles. That is a common path in Ocala. Make sure a metal option is not missing underlayment, flashings, or edge metal that the shingle quote already includes.

Finished Onyx Black Duration ridge on the Silver Springs Shores job.

5. Does the quote say who pulls the permit and when the crew can start?

Confirm which company pulls the reroof permit, who schedules inspections, and how soon after approval the tear-off can begin.

ASAP timing only works when permit and material lead times are written into the plan. Put start windows and permit responsibility on the quote so a low number that cannot start for weeks does not beat a ready crew by surprise. See the Showcase.

Nearby project

Silver Springs Shores, Ocala, FL. About 19 squares of Owens Corning Duration Onyx Black, 3 starter, 2 ProEdge, new black drip edge. Sales: Alex Lawrence. See the Showcase.

FAQs

Should I pick the lowest Silver Springs Shores quote automatically?

No. Use these five checks first so you know whether the low number includes the same system, starter, ridge, drip edge, and permit path. A lower quote that skips finishing materials is not a savings.

Can Brehm help me compare a Duration quote to a metal option?

Yes. Sales consultants like Alex Lawrence routinely walk shingle vs metal options for Ocala homeowners who want ASAP timing depending on price. Bring your other quotes so the scopes can be lined up side by side.

Where is the nearest Brehm office for Silver Springs Shores?

The nearest office for Silver Springs Shores and greater Ocala is our Ocala location at 1729 E Silver Springs Blvd Suite 5. Call 352-664-8887 to schedule a quote walk.

Brehm Roofing provides residential roof replacements throughout Ocala, Gainesville, The Villages, Minneola, and nearby North Central Florida communities.

Get a Free Estimate if you want help comparing Duration Onyx Black or metal options in Silver Springs Shores or greater Ocala.

This Shannon Wood home in Gainesville needed a full shingle replacement on a roof from around 2012. The homeowner wanted to stay with shingles and was not in a rush on the timeline.

We installed about 33 squares of Owens Corning Duration in Onyx Black with 3 starter bundles, 4 bundles of OC ProEdge hip and ridge, and new white drip edge throughout. Sales consultant Alex Lawrence walked the project in Shannon Wood.

We pulled the reroof permit for this job. View the finished project on our Shannon Wood Showcase.

Finished Owens Corning Duration Onyx Black roof in Shannon Wood, Gainesville, FL.

Why Owens Corning Duration Onyx Black for a Shannon Wood reroof?

Owens Corning Duration in Onyx Black was the system chosen for this full Shannon Wood replacement on a roof from around 2012.

The homeowner wanted to stay with architectural shingles rather than switching products. Onyx Black is a dark multi-tone Duration color that fits a residential Gainesville lot. About 33 squares covered this home, with 3 starter bundles and 4 ProEdge hip and ridge bundles finishing the peaks.

Sales consultant Alex Lawrence kept the scope on a planned retail replacement with no rush on the timeline. Age alone was enough reason to replace the system instead of waiting for a leak.

Does a full Gainesville reroof include new drip edge?

Yes. On every full roof replacement we install new drip edge with the new roof system.

This Shannon Wood job used new white drip edge throughout with the Onyx Black Duration field. Edge metal lines the eaves and rakes and protects the deck edge where water leaves the roof. We never reuse old drip edge on a full reroof.

Finished Onyx Black Duration ridge and field on the Shannon Wood job in Gainesville, FL.

What does a finished Duration Onyx Black field look like in Shannon Wood?

This job is a completed reroof with a clean Onyx Black Duration field, matching ProEdge on the ridges, and finished roof planes.

Gainesville homes take Alachua County heat, summer storms, and neighborhood tree cover. A Duration system with new white drip edge is built for that weather on a residential lot.

Finished Onyx Black field with new white drip edge on the Shannon Wood job.

Project details

Detail This project

System / manufacturer Owens Corning Duration architectural shingles

Color Onyx Black

Squares About 33

Starter 3 bundles starter

Hip / ridge 4 bundles OC ProEdge

Drip edge New white (always new on a full reroof)

Project type Full roof replacement

City Shannon Wood, Gainesville, FL

Sales consultant Alex Lawrence

Permit Permit pulled

FAQs

Can a Shannon Wood Duration reroof be done in one day?

Many Brehm full shingle replacements finish in one day when the scope, weather, and crew size line up. About 94 percent of our jobs are done in one day. Your sales consultant will confirm whether a ~33 square Gainesville home like this Shannon Wood job fits a single-day schedule.

Should drip edge and accessories match Onyx Black?

Not always. This Shannon Wood job used new white drip edge with an Onyx Black Duration field. White edge metal is a common finish against dark shingles. Boot and vent colors are chosen to fit the roof and house. Ask your sales consultant which accessory colors fit your elevation.

What maintenance does a new Duration Onyx Black roof need in Gainesville?

Keep valleys and gutters clear of pine needles and leaf litter, and call after a major storm if anything looks out of place. Duration Onyx Black does not need special coatings for normal Alachua County weather. A quick walkaround after big storms is enough for most homeowners in Shannon Wood.

Brehm Roofing provides residential roof replacements throughout Gainesville, Ocala, The Villages, Minneola, and nearby North Central Florida communities. The nearest office for this Shannon Wood job is our Gainesville location at 1344 NW 121st Way.

Get a Free Estimate if you want to talk through an Owens Corning Duration Onyx Black reroof in Shannon Wood or greater Gainesville.